CCNA LAB 8

Cisco Certified Network Associate - CCNA Labs
Network Engineering

(Updated from real CCNA exam on 19-Feb-2009)

Question:

To configure the router (R2-RC) click on the console host icon that is connected to a router by a serial console cable (shown in the diagram as a dashed black line)

Central Florida Widgets recently installed a new router in their office. Complete the network installation by performing the initial router configurations and configuring RIPV2 routing using the router command line interface (CLI) on the R2-RC.

Name of the router is R2-RC
Enable-secret password is cisco1
The password to access user EXEC mode using the console is cisco2
The password to allow telnet access to the router is cisco3
IPV4 addresses must be configured as follows:
Ethernet network 209.165.202.128/27 - router has last assignable host address in subnet
Serial network is 192.0.2.16/28 - router has last assignable host address in the subnet. Interfaces should be enabled.
Router protocol is RIP V2

Attention : In practical examinations, please note the following, the actual information will prevail. s1. Name of the router is xxx 2. Enable-secret password is xxx 3. Password to access user EXEC mode using the console is xxx 4. The password to allow telnet access to the router is xxx 5. IP information

Solution:

-->1) Name the router:

Router>enable
Router#configure terminal
Router(config)#hostname R2-RC

2) Set secret password:

R2-RC(config)# enable secret cisco1

3) Set password for the console:

R2-RC(config)#line console 0
R2-RC(config-line)#password cisco2
R2-RC(config-line)#login
R2-RC(config-line)#exit

4) Set the Telnet password:

R2-RC(config)#line vty 0 4
R2-RC(config-line)#password cisco3
R2-RC(config-line)#login
R2-RC(config-line)#exit

5) Assign IP address for Ethernet interface (Fa0/0):

The Ethernet network 209.165.202.128/27 has:

Increment:32 (/27 = 255.255.255.224 or 1111 1111.1111 1111.1111 1111.1110 0000)
Network address: 209.165.202.128
Broadcast address: 209.165.202.159 (because 128 + 32 - 1 = 159)

Therefore the last assignable host address in this subnet is 209.165.202.158 and we will assign it to Fa0/0 interface with these commands:

R2-RC(config)# interface fa0/0
R2-RC(config-if)#ip address 209.165.202.158 255.255.255.224
R2-RC(config-if)#no shutdown
R2-RC(config-if)#exit

6) Assign IP address for Serial interface (S0/0/0):

Serial network 192.0.2.16/28 has:

Increment:16 (/28 = 255.255.255.240 or 1111 1111.1111 1111.1111 1111.1111 0000)
Network address: 192.0.2.16
Broadcast address: 192.0.2.31 (because 16 + 16 - 1 = 31)

So the last assignable host address in this subnet is 192.0.2.30. Finally we assign it to s0/0/0 interface:

R2-RC(config)# interface s0/0/0
R2-RC(config-if)#ip address 192.0.2.30 255.255.255.240
R2-RC(config-if)#no shutdown
R2-RC(config-if)#exit

7) Configure RIP v2 routing protocol:

R2-RC(config)#router rip
R2-RC(config-router)#version 2
R2-RC(config-router)#network 209.165.202.128
R2-RC(config-router)#network 192.0.2.16
R2-RC(config-router)#end
R2-RC#copy running-config startup-config